This article was originally published in the January/February 1998 issue of Home Energy Magazine. Some formatting inconsistencies may be evident in older archive content.
Home Energy Magazine Online January/February 1998
How Tight Are America's Houses?
The studies describe the overall tightness (or looseness) of U.S. houses and show how tightness varies with the age of the house, type of construction, location, size, and weatherization. Researchers also looked at the total energy picture for the country's building stock, the effect of airtightness on indoor air quality, and ventilation strategies that are cost-effective if houses are tightened to conform to ASHRAE Standard 119.
Before these studies, LBNL maintained a database of blower door test results that included about 240 homes, mostly in California and the Pacific Northwest. Now the database includes 12,946 individual measurements on more than 12,500 single-family detached houses all over the United States.
Leakage results from the database didn't correlate with any climate- or location-related trends. The studies found that leakage trends are more affected by construction quality, local practices, and age distribution than by weather. Table 1 shows minimum, maximum, and mean leakage measurements for the houses in the study and gives minimum, maximum, and mean figures for the age of the houses and the floor areas. Air leakage is expressed in two ways--air changes per hour at 50 Pascals of pressure (ACH50) and normalized leakage (NL). These are the two ways of measuring most commonly used in practice and in standards.Comparison of Variables The first study compares five building criteria that may influence leakage--number of stories, year of construction, type of floor or basement, age of the house, thermal distribution system, and retrofitting. LBNL researchers found a correlation between each of these criteria and the normalized leakage values.
Number of stories. Approximately 56% of the measurements are for multistory houses. Multistory houses were 11% leakier (NL = 1.8) than single-story houses (NL = 1.6).
Type of floor or basement. Two types of house were examined with respect to this issue--houses that had floor leakage to the outdoors (built with crawlspaces or unconditioned basements) and houses that had no floor leakage to outdoors (built slab-on-grade or with fully conditioned basements). The vast majority (80%) of the houses had floor leakage (NL = 1.75). The 20% that did not have floor leakage were 5% tighter overall. This is a minor difference, but statistically significant.
Age of house. Of the houses with information about the year the house was built, those built after 1980 didn't show increasing leakiness with age and were tighter (NL = 0.47) than average. The houses built before 1980 showed increased leakage with age and were on average much leakier (NL = 1.05) than new houses.
Thermal distribution system. Eleven percent of the total sample contained information about the presence (or absence) of a duct system. The surprising result was that the homes with duct systems (43% of this subset) were tighter overall (NL = 0.7) than homes without duct systems (NL = 0.9). Where duct systems were measured separately (about 1% of the total sample), they accounted for just under 30% of the total leakage--a finding consistent with those of other studies.
Retrofitting. Four hundred sixty-five houses were measured as part of retrofit or weatherization projects; measurements were taken both before and after the retrofits were done. These measurements showed that the average retrofit reduced leakage by about 25%.Ventilation Strategies Using the newly expanded LBNL leakage database, the second study analyzes the energy and cost factors associated with providing the current levels of ventilation and estimates the energy savings or penalties associated with tightening or loosening the building envelope while still providing adequate ventilation.
ASHRAE Standard 119-1988, which sets maximum leakage levels of building envelopes based on energy considerations, was used to evaluate the tightness of the housing stock. ASHRAE Standard 62-1989 sets minimum ventilation rates for providing acceptable air quality in all kinds of buildings. For residential buildings, the standard specifies 0.35 ACH. The researchers used an approach similar to ASHRAE Standard 136-1993 to estimate the combined contributions of envelope leakage and other ventilation systems toward meeting Standard 62.
The study looks at natural, exhaust-only, and heat recovery ventilation. It assumes that both the exhaust system and the balanced heat recovery ventilator are sized to provide 0.35 ACH at all times. (Most users would probably not operate these systems at all times, but this assumption helps to avoid overstating the savings associated with the alternative scenarios.) The projections assume three things:
Home Energy can be reached at: email@example.com
- FIRST PAGE
- PREVIOUS PAGE